OPERATING AND ASSEMBLY INSTRUCTIONS

table of contents

| Introduction
| General Tips
| Intended use
| Installation and connection
| Washing and maintenance
| Environmental protection
| Important safety instructions

INTRODUCTION

We would like to thank you for your trust and congratulate you on the purchase of the high-quality LEDWORDS® product from the 3D LED LIGHT GRAPHIC™ series. We have made every effort to ensure that this product pleases your eyes with its charm and serves you for as long as possible.

For more information about our products, please visit our website www.ledwords.pl . You are also welcome to visit our store www.ledwords.eu . There are a lot of very interesting and ready-made products with fast shipping.

IMPORTANT! After unpacking, check the condition of the product. Do not connect if the device has been damaged during transportation.

GENERAL GUIDELINES

These instructions were prepared on the basis of a product in the form of a circle. Depending on the model, the shape of the product may be different from a circle. In this case, follow the same procedure during installation. The shape does not change the rules of assembly and operation.

• Read this manual carefully. Familiarizing yourself with the information contained therein will allow you to use the product properly and safely. Keep the operating and installation instructions for future reference. Safe operation of the product is ensured only by proper installation according to the installation instructions. The installer is responsible for proper operation at the installation site. The product is designed to be mounted on a wall or ceiling, indoors or outdoors. The expected place of operation of the product is the interior wall of the building, mounting on the prepared bracket and connecting the cable with a plug.
• NOTE! The standard installed quick-mount bracket allows you to independently mount the product only to an interior wall in the building (indoor adaptation).
• The condition for the installation of the product including its disassembly (installation on the ceiling or outside the building) is the installation carried out by a specialist with the appropriate authorization (electrical installer). The manufacturer is not responsible for damage caused by improper installation by unauthorized persons.
• The product has the ability to work with controllers that automate the switching on and off of backlighting at specific times, such as twilight automatics.
• The supply voltage should be between 110V and 230V. The power plug is of the European type. For connection to other outlets, you can use a suitable adapter or replace the plug.

INTENDED USE

• This product is intended as a striking light decoration for mounting on a wall or ceiling, indoors or outdoors. The standard installed mounting bracket allows you to independently mount the product only to the wall, inside the building. In the outgoing cable is installed at the end of an ordinary straight plug having two pins with a spacing of 19mm. If the plug does not fit into the wall-mounted socket, you need to purchase a special adapter (available in the online store) or replace the plug yourself with any type. Carrying out the installation with unscrewing the product is possible only by qualified persons, familiar with electrical engineering. The manufacturer is not responsible for damage caused by improper installation, alteration or incorrect operation. Improper installation poses a risk of electric shock or falling of the product.
• Safety during use is ensured only by proper installation in accordance with the installation instructions. The installer is responsible for proper operation at the product installation site.
• The product is not intended to be operated by children and persons with limited fitical, sensory or mental abilities, or by persons who do not have sufficient knowledge and experience with the operation of electrical equipment. The product should only be operated by persons who are aware of the risks involved. Do not allow children to play with the product! Cleaning and maintenance operations must not be performed by children unless they are at least 15 years old and supervised by an adult. Children under the age of 8 should not go near the product and especially its power cord.

INSTALLATION AND CONNECTION

• IMPORTANT: Before drilling for mounting studs, make sure that there are no electrical wires or other cables or pipes in the drilling area that could be damaged.
• INSTALLATION TIPS: The product is in 3D, that is, it consists of a front, side and back. The front with the side (frame) is permanently connected and forms the shade(front cover). Only the back cover is detachable. It should be removed and attached to the wall or ceiling in the first place.
• You can drill holes in the back cover for mounting pins only in appropriate places. It is possible to insert and install a cable protruding from the wall (if any). Be careful not to damage the LED installation!

• To remove the back cover, remove all visible screws (Bit Ph1).
• IMPORTANT NOTE! It is safe to drill holes in the back cover for mounting studs and for the cable protruding from the wall (if prepared).

• SUBSTRATE PREPARATION: The wall should be flat, level and have sufficient bearing capacity. The depth of the holes must be the same as the length of the screws. The wall studs must be securely seated. The included screws and wall plugs are designed for solid masonry walls. For other types of walls (e.g., gypsum board, porous concrete, Poroton brick), use the appropriate type of fastening material. They are available at home improvement stores.
• LED modules and a 12V power supply are installed in the back cover. One side is permanently connected to the modules (integral part). The other side is an output prepared for connection to electricity.

• Screw the back cover to the wall or ceiling. Use the appropriate wall plugs.
• You can drill holes in the back cover for mounting pins only in safe places so as not to damage the LED installation!

• After completing all the necessary installation steps, apply the front cover and tighten all the screws.
  
  IMPORTANT! The cover is fragile and special care must be taken. The cover must be well-fitted (as it was before it was taken apart) to prevent water from getting inside!

Be sure to keep the screws in mind!

WASHING AND MAINTENANCE

• The surfaces of the product are very sensitive. When washing, avoid aggressive cleaning agents. Wash the product gently and by hand using a micro-fiber cloth. Paper may scratch the surfaces. We recommend using warm water with dishwashing liquid. To avoid damage to various types of surfaces due to the use of inappropriate cleaning agents, please follow the instructions below.
• Do not use the product for washing:
  • Corrosive cleaners or scouring agents, such as scouring powder or lotion
  • Cleaning agents with a high alcohol content,
  • Rough sponges and wire brushes,
  • High-pressure washers and steam cleaners,
  • solvents,
  • aggressive all-purpose cleaners.

WARNING! Danger of product damage and short circuit! Do not use high-pressure washers or steam cleaners to wash the product.

ENVIRONMENTAL PROTECTION

The product is characterized by high energy efficiency (LED). This section provides advice on how to operate the device in an energy-saving manner and how to dispose of it properly.

Tip: When using the device outdoors, we suggest not turning the backlight on during the day, as daylight dulls the effect of the product's glow (the difference is usually hardly noticeable). We suggest installing a twilight automatic or other controller that automates the switching of the backlight on and off at optimal times.

DISPOSAL OF USED PRODUCT:

Dispose of the used product in accordance with environmental regulations. The user is obliged to give it to collectors of waste electrical and electronic equipment. The collectors, including local collection points, stores and municipal units, shall establish an appropriate system for handing over this type of product. Proper handling of waste electrical and electronic equipment contributes to avoiding harmful consequences for human health and the environment resulting from the presence of hazardous components and improper storage and processing of such equipment. Let's take care of the environment together!

SAFETY TIPS

After unpacking, check the condition of the product. Do not connect if the product has been damaged during transportation. The safe operation of the product is ensured only by correct installation in accordance with the installation instructions. The installer is responsible for proper operation at the installation site.

The surfaces of the product are very sensitive. When installing, please proceed gently to avoid unwanted damage. Product improperly attached, may fall! All fasteners must be installed carefully and accurately.

A damaged product can lead to electric shock! Never turn on a damaged device. Pull the plug from the socket or disconnect the fuse in the fuse box and call for service or send the product for repair as soon as possible.

NOTE!

Danger of electric shock! Improperly performed repairs pose a serious hazard. Only authorized persons may carry out repairs and replace damaged components. If the product is damaged, unplug it or disconnect the fuse in the fuse box.

Never twist, bend or crimp the electric wire. Damage to the cable and short circuit may occur. Any alteration or modification of the mechanical design of the product and its electrical system is dangerous and may cause malfunction. Do not make any modifications. Any type of modification will result in loss of warranty.

After unpacking, check the condition of the product. Do not connect if the device has been damaged during transportation.

IMPORTANT!

The light emitted by LED modules is very bright and can damage your eyesight. Do not look directly at the turned-on LED modules for more than 100 seconds.

WARNING!

Danger of suffocation! The packaging is dangerous for children. Do not allow children to play with the packaging!

It is worth trusting the specialists. This way you get a guarantee of reliable and professional repair using original spare parts for the product.

Contact form